Showing 1–14 of 18 resultsSorted by latest

Victron Cerbo GX MK2

Original price was: R5, 599,35.Current price is: R3, 689,00.

This all-new communication-centre allows you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch, a MFD or our VictronConnect App thanks to its added Bluetooth capability. The RJ45 ports have been rotated for easier access to remove cables.

Victron Energy Smartshunt 500A/50mV IP65

R1, 511,00

The SmartShunt IP65 is an all-in-one battery monitor, only without a display. Your phone acts as the display.

The SmartShunt IP65 is water resistant and is available in a 500 A version.
The SmartShunt IP65 connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.

Alternatively, the SmartShunt IP65 can be connected and be read by a GX device.

Connection to the SmartShunt is made via a VE.Direct cable.

The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.

The SmartShunt is equipped with Bluetooth, has a VE.Direct port and an auxiliary connection that can be used to monitor a second battery, for midpoint monitoring, or to connect a temperature sensor.

 

Victron BatteryProtect 12/24V-65A

R749,00

The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The Battery Protect is a uni-directional device. It can only deal with current in one direction, so either current to a load, or current from a charger, but not both currents at the same time. In addition to this, current only can only flow from the Battery terminal to the Load terminal. In case of use with a load, the battery connects to the Battery terminal, and in case of use with a charger, the charger connects to the Battery terminal.

Voltage: 12/24V
Current: 65A

Victron Blue Smart Battery Charger – IP65 – 12V 10A – IEC 7/17 Plug

R1, 795,00

Victron SmartShunt 300A/50mV IP65

R1, 510,00

Victron Battery Balancer

R1, 090,00
The Battery Balancer equalizes the state of charge of two series connected 12V batteries, or of several parallel strings of series connected batteries.

Victron 2 meter Extension Cable for IP 65 Blue Smart Battery Chargers

R210,00

Victron 2 meter Extension Cable for IP 65 Blue Smart Battery Chargers

The 2 meter extension cable is an accessory of the Blue Smart IP65 Charger with DC connector.

 

Victron Battery Indicator Panel (M8 eyelet connector / 30A ATO fuse)

R475,00

Victron Battery Indicator Panel Battery Indicator Panel

M8 eyelet connector / 30A ATO fuse

Cable Length: 1.5 m

Cable c.s.a: 3.3 mm2 / 12 AWG

Maximum Current: 20 Amps

A Practical solution for Battery Management suited for all BPC/BSC Chargers with DC Connector

The battery indicator shows the status of the battery.

It is an accessory for the Blue Smart and Blue Power IP65 Chargers. It is suitable for 12V lead acid batteries only (flooded, GEL, AGM)

After using the battery it takes about 30 minutes for the battery to regain its steady state condition and for the panel to show a correct status indication.

Green light: Battery does not need to be charged. Battery 80%-100%

Orange light: Battery can be charged. Battery 60%-80%

Red light: Battery needs charging.

Battery 40%-60% No light: charge immediately to prevent sulfation. Battery <40%

Click here to download specifications leaflet

Victron Rubber Bumper for Blue Smart IP65 Charger 12/10, 12/15, 24/8

R155,00

Victron Rubber Bumper for IP65 Charger 12/10, 12/15 & 24/8

The IP65 Charger is already protected against dust, and water spray – now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life. It will extend the life of your charger, and it has an easy-carry handle,or hang it from a hook when not in use.

Victron Wall Mount for Blue Smart IP65 Charger 12/10, 12/15, 24/8

R110,00

Victron Wall Mount for Blue Smart IP65 Charger 12/10, 12/15, 24/8

This Wall Mount will be especially useful if you like to keep your smart charger handy – above your workshop bench, for example. Now the charger can be used without even moving it!

(Batteries, Charger, and accessories not included)

 

 

Victron Blue Smart Battery Charger – IP65 – 12V 15A with IEC 7/16 IEC Plug

R2, 070,00

Victron Blue Smart Battery Charger – IP65 – 12V 15A – Smart Charger

Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.

7 Step “Smart” Battery Charger

180 to 265 V AC Input

12 Volt DC Output

15 Amp @ 12 V (14,4 – 14,7 V)

IP 65 WaterProof

IEC 7/16 IEC Plug

Free Bluetooth Monitoring & Control App

 

Victron Blue Smart IP65 Charger 24V 8 A IEC 7/16 Plug

R2, 070,00

Victron Blue Smart Battery Charger – IP65 – 24V 8A – Smart Charger

Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.

7 Step “Smart” Battery Charger

180 to 265 V AC Input

24 Volt DC Output

8 Amp @ 24 V (28,8 – 29,4 V)

IP 65 WaterProof

Free Bluetooth Monitoring & Control App

Victron Battery Monitor BMV-712 Smart with Bluetooth App Retail

R2, 399,00

Victron BMV-712 Smart Dual Battery Monitor with Panel Indicator, Shunt and Bluetooth App

Cable Length: 1.5 m

Cable c.s.a: 3.3 mm2 / 12 AWG

Maximum Current: 20 Amps

(Batteries, Charger, and accessories not included)